Cisco Nexus 2000 Series NX-OS Fabric Extender Configuration Guide for Cisco Nexus 9000 Series Switches, Release 7.x - Configuring the Fabric Extender [Cisco Nexus 2000 Series Fabric Extenders] (2024)

Table of Contents
Managing the Fabric Extender Feature Set Installing the Fabric Extender Feature Set Enabling the Fabric Extender Feature Set Associating a Fabric Extender to a Fabric Interface Configuring Fabric Extender Global Features Configuration Examples Verifying the Configuration Verifying the Fabric Extender Configuration Verifying the Chassis Management Information Additional References Related Documents

This chapter describes how to configure a Cisco Nexus 2000 Series Fabric Extender using a parent device and includes the following sections:

Managing the Fabric Extender Feature Set

Installing the Fabric Extender Feature Set

Procedure

Command or Action Purpose

Step1

configure terminal

Example:

switch# configure terminalswitch(config)#

Enters global configuration mode.

Step2

install feature-set fex

Example:

switch(config)# install feature-set fex

To uninstall the Fabric Extender feature set, use the no install feature-set fex command.

Note

Before you can uninstall the feature set, you must ensure that the feature set is installed in the default VDC and that the feature set is not enabled in any VDC.

Step3

exit

Example:

switch(config)# exitswitch#

Exits global configuration mode.

Enabling the Fabric Extender Feature Set

You can enable the installed Fabric Extender feature set in a VDC on the device.

Procedure

Command or Action Purpose

Step1

configure terminal

Example:

switch# configure terminalswitch(config)#

Enters global configuration mode.

Step2

feature-set fex

Example:

switch(config)# feature-set fex

Enables the Fabric Extender feature set. The feature set must be installed before it shows as an option to this command.

To disable the Fabric Extender feature set, use the no feature-set fex command.

Note

The no feature-set fex command might take some time to complete if the size of the configuration is very large. The command cleans up all of the configurations associated with the Fabric Extender feature set.

Step3

exit

Example:

switch(config)# exitswitch#

Exits global configuration mode.

Associating a Fabric Extender to a Fabric Interface

Associating a Fabric Extender to a Port Channel

Before you begin

Ensure that you have enabled the Fabric Extender feature set.

Procedure
Command or Action Purpose

Step1

configure terminal

Example:
switch# configure terminalswitch(config)#

Enters global configuration mode.

Step2

interface port-channel channel

Example:
switch(config)# interface port-channel 4switch(config-if)#

Specifies a port channel to configure.

Step3

switchport mode fex-fabric

Example:
switch(config-if)# switchport mode fex-fabric

Sets the port channel to support an external Fabric Extender.

Step4

fex associate FEX-number

Example:
switch(config-if)# fex associate 101

Associates a FEX number to the Fabric Extender unit attached to the interface. The range is from 101 to 199.

Step5

(Optional) show interface port-channel channel fex-intf

Example:
switch# show interface port-channel 4 fex-intf
 (Optional)

Displays the association of a Fabric Extender to a port channel interface.

Example

This example shows how to associate the Fabric Extender to a port channel interface on the parent device: 

switch# configure terminalswitch(config)# interface ethernet 1/28switch(config-if)# channel-group 4switch(config-if)# no shutdownswitch(config-if)# exitswitch(config)# interface ethernet 1/29switch(config-if)# channel-group 4switch(config-if)# no shutdownswitch(config-if)# exitswitch(config)# interface ethernet 1/30switch(config-if)# channel-group 4switch(config-if)# no shutdownswitch(config-if)# exitswitch(config)# interface ethernet 1/31switch(config-if)# channel-group 4switch(config-if)# no shutdownswitch(config-if)# exitswitch(config)# interface port-channel 4switch(config-if)# switchportswitch(config-if)# switchport mode fex-fabricswitch(config-if)# fex associate 101
Cisco Nexus 2000 Series NX-OS Fabric Extender Configuration Guide for Cisco Nexus 9000 Series Switches, Release 7.x - Configuring the Fabric Extender [Cisco Nexus 2000 Series Fabric Extenders] (1)

Note

  • The fex associate command must be entered from the port channel interface, not from the physical interface.

  • When adding physical interfaces to port channels, all configurations on the port channel and physical interface must match.

This example shows how to display the association of the Fabric Extender and the parent device: 

switch# show interface port-channel 4 fex-intfFabric FEXInterface Interfaces---------------------------------------------------Po4 Eth101/1/48 Eth101/1/47 Eth101/1/46 Eth101/1/45 Eth101/1/44 Eth101/1/43 Eth101/1/42 Eth101/1/41 Eth101/1/40 Eth101/1/39 Eth101/1/38 Eth101/1/37 Eth101/1/36 Eth101/1/35 Eth101/1/34 Eth101/1/33

Disassociating a Fabric Extender from an Fabric Interface

Before you begin

Ensure that you have enabled the Fabric Extender feature set.

Procedure
Command or Action Purpose

Step1

configure terminal

Example:
switch# configure terminalswitch(config)#

Enters global configuration mode.

Step2

interface port-channel channel

Example:
switch(config)# interface port-channel 4switch(config-if)#

Specifies a port channel to configure.

Step3

no fex associate <FEX-id>

Example:
switch(config-if)# no fex associate 101

Disassociates the Fabric Extender unit attached to the interface.

Step4

default interface ethernet <interface>

Example:
switch(config)# default interface ethernet 1/1

Sets the default settings for the member interface of the fabric port channel.

Step5

no fex <FEX-id>

Example:
switch(config)# no fex 101

Removes the FEX configuration.

Configuring Fabric Extender Global Features

You can configure global features on the Fabric Extender.

Before you begin

Ensure that you have enabled the Fabric Extender feature set.

Procedure

Command or Action Purpose

Step1

configure terminal

Example:

switch# configure terminalswitch(config)#

Enters global configuration mode.

Step2

fex FEX-number

Example:

switch(config)# fex 101switch(config-fex)#

Enters FEX configuration mode for the specified Fabric Extender. The range of the FEX-number argument is from 101 to 199.

Note

If you need to change the FEX number, you must remove the previous configuration (using the no fex FEX-number command) before applying a new FEX number.

Step3

(Optional) locator-led fex FEX-number

Example:

switch(config)# locator-led fex 101
 (Optional)

Turns on the locator LED of a Fabric Extender. The range of the FEX-number argument is from 101 to 199.

Step4

(Optional) description desc

Example:

switch(config-fex)# description Rack7A-N2K
 (Optional)

Specifies the description. The default is the string FEXxxxx where xxxx is the FEX number. If the FEX number is 123, the description is FEX0123.

Step5

(Optional) no description

Example:

switch(config-fex)# no description
 (Optional)

Deletes the description.

Step6

(Optional) no type

Example:

switch(config-fex)# no type
 (Optional)

Deletes the FEX type. When a Fabric Extender is connected to the fabric interfaces and does not match the configured type that is saved in the binary configuration on the parent switch, all configurations for all interfaces on the Fabric Extender are deleted.

Step7

(Optional) serial serial

Example:

switch(config-fex)# serial JAF1339BDSK
 (Optional)

Defines a serial number string. If this command is configured, a switch allows the corresponding chassis ID to associate (using the fex associate command) only if the Fabric Extender reports a matching serial number string.

Caution

Configuring a serial number that does not match the specified Fabric Extender forces the Fabric Extender offline.

Step8

(Optional) no serial

Example:

switch(config-fex)# no serial
 (Optional)

Deletes the serial number string.

Configuration Examples

This section contains examples of FEX configurations.

Configuring a Host Interface in a vPC Topology Connected to Two FEXs

This example shows how to configure a host vPC with a FEX (host vPC attached to two different FEXs):

Switch 1 Configuration Switch 2 Configuration 
config tfeature lacpint e101/1/1-2channel-group 10 mode activeno shutdownInt port-channel10switchport switchport mode trunk switchport trunk allowed vlan 1-20vpc 10
 
config tfeature lacpint e101/1/1-2channel-group 10 mode activeno shutdownInt port-channel10switchport switchport mode trunk switchport trunk allowed vlan 1-20vpc 10

Switch vPC Topology and Straight Through FEX Topologies (Host vPC)

The Straight through FEX is supported on the Cisco Nexus 9300-FX2 platform. Beginning with Cisco NX-OS Release 9.3(5) it is supported on the Cisco Nexus 9300-FX3 platform also.

In Cisco NX-OS Release 9.3(5), the following third-party equipment is not supported for straight-through FEX for Cisco Nexus 9300-FX3 platform switches: B22-HP, B22-IBM, B22-Dell, and B22-Fujitsu.

The following is an example of a straight through FEX topology:


Cisco Nexus 2000 Series NX-OS Fabric Extender Configuration Guide for Cisco Nexus 9000 Series Switches, Release 7.x - Configuring the Fabric Extender [Cisco Nexus 2000 Series Fabric Extenders] (2)

Note that this topology shows:

  • The Cisco Nexus 9000 Series switch ports are directly connected to another switch or host and are configured as part of a port channel that becomes part of a vPC.

  • That vPC 20 is configured on port channel 20, which has Eth1/10 on N9k-1 and Eth2/1 on N9k-2 as members.


Cisco Nexus 2000 Series NX-OS Fabric Extender Configuration Guide for Cisco Nexus 9000 Series Switches, Release 7.x - Configuring the Fabric Extender [Cisco Nexus 2000 Series Fabric Extenders] (3)

Note that this topology shows:

  • Each FEX is single-homed (straight-through FEX topology) with a Cisco Nexus 9000 Series switch. The host interfaces on this FEX are configured as port channels and those port channels are configured as vPCs.

  • Eth100/1/1 on N9k-1 and Eth102/1/5 on N9k-2 are configured as members of PO200 and PO200 is configured for vPC 200.

In both topologies, port channels P020 and P0200 must be configured identically on the peer switches and configuration synchronization is used to synchronize the configurations of the vPC switches.

The following table compares the sample running configuration that must be configured for the peer switches shown in the Switch vPC Topology and the FEX Straight-Through Topology (Host vPC).

Table 1. Running Configuration Example for a vPC Straight-Through Topology

Basic Configuration—No Port Profile

Port Profile Configuration 

vlan 1-10
 
vlan 1-10
 
interface port-channel 20 switchport mode trunk vpc 20 switchport trunk allowed vlan 1-5
 
port-profile type port-channel pc-profile switchport mode trunk state enabled
 
interface port-channel 200 switchport mode trunk vpc 200 switchport trunk allowed vlan 1-5
 
interface port-channel 20 inherit port-profile pc-profile vpc 20 switchport trunk allowed vlan 1-5
 
interface Ethernet1/10 switchport mode trunk switchport trunk allowed vlan 1-5 channel-group 20
 
interface port-channel 200 inherit port-profile pc-profile vpc 200 switchport trunk allowed vlan 1-5
 
interface Ethernet100/1/1 switchport mode trunk switchport trunk allowed vlan 1-5 channel-group 200
 
interface Ethernet1/10 switchport mode trunk switchport trunk allowed vlan 1-5 channel-group 20
 
interface Ethernet100/1/1 switchport mode trunk switchport trunk allowed vlan 1-5 channel-group 200
New Deployment in a vPC Topology and Straight-Through FEX Topology

In a new deployment, configuration synchronization is introduced initially to synchronize the new configuration. Because it is a new deployment, there is no existing running configuration on the FEX ports.

The following example shows how to configure the peer switches in the Switch vPC Topology and the FEX Straight-Through Topology (Host vPC):

See Also
NMEA 2000 PGN’s deciphered - ENDIGE BOATINGCisco Nexus 2000 Series Fabric Extenders Data Sheet

  • Configure the CFS over IPV4 distribution to change the multicast address. 

    N9k-1(config)# no cfs ipv4 distributeThis will prevent CFS from distributing over IPv4 networkAre you sure? (y/n) [n] yN9k-2(config)# no cfs ipv4 distributeThis will prevent CFS from distributing over IPv4 network.Are you sure? (y/n) [n] y

  • Configure the CFSoIP multicast address on each peer switch 

    N9k-1(config)# cfs ipv4 mcast-address 239.255.1.1Distribution over this IP type will be affectedChange multicast address for CFS-IP?Are you sure? (y/n) [n] yN9k-2# config terminalN9k-2(config)# cfs ipv4 mcast-address 239.255.1.1Distribution over this IP type will be affectedChange multicast address for CFS-IP?Are you sure? (y/n) [n] y

  • Enable CFSoIP on both switches. 

    N9k-1(config)# cfs ipv4 distributeN9k-2(config)# cfs ipv4 distribute

  • Create a switch profile and configure the peer on both switches. 

    N9k-1# config syncN9k-1(config-sync)# switch-profile TestN9k-1(config-sync-sp)# sync-peers destination <out of band mgmt0 IP address of peer switchN9k-2>N9k-2# config syncN9k-2(config-sync)# switch-profile TestN9k-2(config-sync-sp)# sync-peers destination <out of band mgmt0 IP address of peer switchN9k-1>

  • Add the referred global configuration to the switch profile. Because the configuration on the interfaces will be synchronized, all policies that are applied on the interface must be synchronized (for example, port profiles, QoS and ACL policies). 

    N9k-1(config-sync-sp)# port-profile type port-channel pc-profileN9k-1(config-sync-port-prof)# switchport mode trunkN9k-1(config-sync-port-prof)# state enabled

  • Create port-channel interfaces inside the switch profile.

    Cisco Nexus 2000 Series NX-OS Fabric Extender Configuration Guide for Cisco Nexus 9000 Series Switches, Release 7.x - Configuring the Fabric Extender [Cisco Nexus 2000 Series Fabric Extenders] (4)

    Note

    Use switch profile mode to create the port-channel interfaces. 

    N9k-1(config-sync-sp)# interface port-channel 20N9k-1(config-sync-sp)# interface port-channel 200

  • Commit the configuration in the switch profile. 

    N9k-1(config-sync-sp)# commit

  • Add members to the port channel in configuration terminal mode on both switches. When the configuration is done in configuration terminal mode, both switches must be configured independently.

    Cisco Nexus 2000 Series NX-OS Fabric Extender Configuration Guide for Cisco Nexus 9000 Series Switches, Release 7.x - Configuring the Fabric Extender [Cisco Nexus 2000 Series Fabric Extenders] (5)

    Note

    In this topology, port-channel members must not be identical on the peer switches. 

    N9k-1(config)# interface Ethernet1/10N9k-1(config-if)# channel-group 20 forceN9k-1(config)# interface Ethernet100/1/1N9k-1(config-if)# channel-group 200 forceN9k-2(config)# interface Ethernet2/1N9k-2(config-if)# channel-group 20 forceN9k-2(config)# interface Ethernet102/1/5N9k-2(config-if)# channel-group 200 force
    N9k-1(config)# interface Ethernet100/1/1N9k-1(config-if)# switchport mode trunkN9k-1(config-if)# switchport trunk allowed vlan 1-5N9k-2(config)# interface Ethernet2/1N9k-2(config-if)# switchport mode trunkN9k-2(config-if)# switchport trunk allowed vlan 1-5N9k-2(config)# interface Ethernet102/1/5N9k-2(config-if)# switchport mode trunkN9k-2(config-if)# switchport trunk allowed vlan 1-5

  • Modify the port-channel configuration in the switch profile. 

    N9k-1(config-sync-sp)# interface port-channel 20N9k-1(config-sync-sp-if)# inherit port-profile pc-profileN9k-1(config-sync-sp-if)# vpc 20N9k-1(config-sync-sp-if)# switchport trunk allowed vlan 1-5N9k-1(config-sync-sp)# interface port-channel 200N9k-1(config-sync-sp-if)# inherit port-profile pc-profileN9k-1(config-sync-sp-if)# vpc 200N9k-1(config-sync-sp-if)# switchport trunk allowed vlan 1-5

  • Commit the configuration in the switch profile. 

    N9k-1(config-sync-sp)# commit
Existing Deployments in a vPC Topology and Straight-Through FEX Topology

In an existing deployment, the configurations are already present and configuration synchronization is used to simplify future configuration modifications.

The following example shows how to configure the peer switches in the Switch vPC Topology and the FEX Straight-Through Topology (Host vPC):

  • Configure the CFS over IPV4 distribution to change the multicast address 
    N9k-1(config)# no cfs ipv4 distributeThis will prevent CFS from distributing over IPv4 networkAre you sure? (y/n) [n] yN9k-2(config)# no cfs ipv4 distributeThis will prevent CFS from distributing over IPv4 network.Are you sure? (y/n) [n] y
  • Configure the CFSoIP multicast address on each peer switch 
    N9k-1(config)# cfs ipv4 mcast-address 239.255.1.1Distribution over this IP type will be affectedChange multicast address for CFS-IP?Are you sure? (y/n) [n] yN9k-2# config terminalN9k-2(config)# cfs ipv4 mcast-address 239.255.1.1Distribution over this IP type will be affectedChange multicast address for CFS-IP?Are you sure? (y/n) [n] y
  • Enable CFSoIP on both switches. 
    N9k-1(config)# cfs ipv4 distributeN9k-2(config)# cfs ipv4 distribute
  • Create a switch profile on both switches. 
    N9k-1# config syncN9k-1(config-sync)# switch-profile TestN9k-2# config syncN9k-2(config-sync)# switch-profile Test
  • Import the running configuration. 
    N9k-1(config-sync-sp)# import running-configN9k-1(config-sync-sp-import)# show switch-profile Test buffer
    Import the configuration to the switch profile on both switches. You can import the configuration using one of the following three methods:

    • Running configuration—All configurations that are allowed inside a switch profile are imported.

      You must remove unwanted configurations. For example, you must remove port-channel member configurations.

    • Interface configuration—Only specified interface configurations are imported.

    • Manual mode—Selected configurations are imported. If the configuration that needs to be imported is small, use the manual mode to paste the desired configuration.

      The following shows the command sequence to import the running configuration:

      Table 2. Command Sequence to Import the Running Configuration

      Buffer Sequence Number

      Command 

      1
      		 
      vlan 1-10
      		 
      22.12.22.3
      		 
      interface port-channel20 switchport mode trunk vpc 20 switchport trunk allowed vlan 1-5
      		 
      33.13.2
      		 
      interface port-channel100 switchport mode fex-fabric fex associate 101
      		 
      44.14.24.3

      Note

      Switch vPC Topology 

      interface port-channel20 switchport mode trunk vpc 20 switchport trunk allowed vlan 1-5
      		 
      44.14.24.3

      Note

      FEX Straight-Through Topology (Host vPC) 

      interface port-channel200 switchport mode trunk vpc 200 switchport trunk allowed vlan 1-5
      		 
      55.15.25.3
      		 
      interface Ethernet1/1 fex associate 101 switchport mode fex-fabric channel-group 100
      		 
      66.16.26.3
      		 
      interface Ethernet1/2 fex associate 101 switchport mode fex-fabric channel-group 100
      		 
      77.17.27.3
      		 
      interface Ethernet1/10 switchport mode trunk switchport trunk allowed vlan 1-5 channel-group 20
      		 
      88.18.28.3
      		 
      interface Ethernet100/1/1 switchport mode trunk switchport trunk allowed vlan 1-5 channel-group 200
      		 
    N9k-2(config-sync-sp)# import running-config
  • (Optional) If you do not want to synchronize the fabric configuration, remove the fabric configuration and the member interfaces of PO 20 and PO 200 from the buffer. 
    N9k-1(config-sync-sp-import)# buffer-delete 3,5,6-8

    The buffer-delete command deletes the unwanted configuration from the buffer.

  • Commit the configuration in the switch profile on both switches. 
    N9k-1(config-sync-sp-import)# commitN9k-2(config-sync-sp-import)# commit

  • Add the sync peer on both switches.

    Cisco Nexus 2000 Series NX-OS Fabric Extender Configuration Guide for Cisco Nexus 9000 Series Switches, Release 7.x - Configuring the Fabric Extender [Cisco Nexus 2000 Series Fabric Extenders] (6)

    Note

    When importing a configuration, use the sync-peers command after you import configurations on both switches independently. 

    N9k-1# config syncN9k-1(config-sync)# switch-profile TestN9k-1(config-sync-sp)# sync-peers destination <out of band mgmt0 IP address of peer switchN9k-2>N9k-2# config syncN9k-2(config-sync)# switch-profile TestN9k-2(config-sync-sp)# sync-peers destination <out of band mgmt0 IP address of peer switchN9k-1>
    N9K-1# configure syncEnter configuration commands, one per line. End with CNTL/Z.N9K-1(config-sync)# no switch-profile SP ? all-config Deletion of profile, local and peer configurations local-config Deletion of profile and local configuration profile-only Deletion of profile only and no other configuration N9396PX-1(config-sync)# no switch-profile SP
    Cisco Nexus 2000 Series NX-OS Fabric Extender Configuration Guide for Cisco Nexus 9000 Series Switches, Release 7.x - Configuring the Fabric Extender [Cisco Nexus 2000 Series Fabric Extenders] (7)

    Caution

    When you remove a switch profile using the no switch-profile name [all-config | local-config] command, the configuration in the switch profile is immediately removed from the running configuration. This disrupts the configurations that were present in the switch profile, such as port channel and vPC configurations.

    When you remove a switch profile using the no switch-profile name [profile-only] command, the configuration in the switch profile is immediately removed from the switch profile only. This does not disrupt the configurations that were present in running config.

    It is recommended to execute the CLI resync-database on both peer switches before deleting a large configuration in the switch-profile.

    Perform the following action if you received the "Deletion of switch profile failed" error message when attempting to delete switch-profile:
     N9K-1(config-sync)# resync-databaseRe-synchronization of switch-profile db takes a few minutes...Re-synchronize switch-profile db completed successfully.N9K-1(config-sync)#N9K-2(config-sync)# resync-databaseRe-synchronization of switch-profile db takes a few minutes...Re-synchronize switch-profile db completed successfully.N9K-2(config-sync)#

Dual-Homed FEX Topology (Active-Active FEX Topology)

The dual-homed FEX (active-active) topology is supported beginning with Cisco NX-OS Release 7.0(3)I5(2) for Cisco Nexus 9300 and 9300-EX Series switches.

The following topology shows that each FEX is dual-homed with two Cisco Nexus 9300 Series switches. The FEX-fabric interfaces for each FEX are configured as a vPC on both peer switches. The host interfaces on the FEX appear on both peer switches.

Cisco Nexus 2000 Series NX-OS Fabric Extender Configuration Guide for Cisco Nexus 9000 Series Switches, Release 7.x - Configuring the Fabric Extender [Cisco Nexus 2000 Series Fabric Extenders] (8)

Note

The port configuration should be the same on both switches.

Cisco Nexus 2000 Series NX-OS Fabric Extender Configuration Guide for Cisco Nexus 9000 Series Switches, Release 7.x - Configuring the Fabric Extender [Cisco Nexus 2000 Series Fabric Extenders] (9)

In the dual-homed FEX topology, the vPC is already operational. FEX 101 is dual-homed to both parent switches: N9k-1 and N9k-2 on FEX-fabric interfaces Ethernet 1/1.

Cisco Nexus 2000 Series NX-OS Fabric Extender Configuration Guide for Cisco Nexus 9000 Series Switches, Release 7.x - Configuring the Fabric Extender [Cisco Nexus 2000 Series Fabric Extenders] (10)

Note

A port channel within the same FEX is supported on Cisco Nexus 2200 Series Fabric Extenders.

FEX 101 is configured to have two types of host interfaces. One interface is Ethernet100/1/1, which is singly attached to a server (nonport-channel member), and the other interface is Ethernet 100/1/2-3, which is configured in a port channel to the server (port-channel member).

The following table shows the sample running configuration for the peer switches. Two types of configurations are shown:

  • Basic Configuration.

  • Port profile configuration.

You can use either option or you can use both configurations together.

Cisco Nexus 2000 Series NX-OS Fabric Extender Configuration Guide for Cisco Nexus 9000 Series Switches, Release 7.x - Configuring the Fabric Extender [Cisco Nexus 2000 Series Fabric Extenders] (11)

Note

You can use port profiles to reduce operational overhead although they are not required.

Table 3. Running Configuration of a FEX in a Dual-Homed Topology for the Peer Switches

Basic Configuration—No Port Profile

Port Profile Configuration 

vlan 1-10
 
vlan 1-10
 
interface port-channel100 switchport mode fex fabric vpc 100 fex associate 101
 
port-profile type ethernet eth-profile switchport mode trunk state enabled
 
interface port-channel 200 switchport mode trunk switchport trunk allowed vlan 1-5
 
port-profile type port-channel pc-profile switchport mode trunk state enabled
 
interface Ethernet1/1 fex associate 101 switchport mode fex fabric channel-group 100
 
interface port-channel100 switchport mode fex fabric vpc 100 fex associate 101
 
interface Ethernet100/1/1 switchport mode trunk switchport trunk allowed vlan 1-10
 
interface port-channel 200 inherit port-profile pc-profile switchport trunk allowed vlan 1-5
 
interface Ethernet100/1/2 switchport mode trunk switchport trunk allowed vlan 1-5 channel-group 200
 
interface Ethernet1/1 fex associate 101 switchport mode fex fabric channel-group 100
 
interface Ethernet100/1/3 switchport mode trunk switchport trunk allowed vlan 1-5 channel-group 200
 
interface Ethernet100/1/1 inherit port-profile eth-profile switchport trunk allowed vlan 1-10
 
interface Ethernet100/1/2 switchport mode trunk switchport trunk allowed vlan 1-5 channel-group 200
 
interface Ethernet100/1/3 switchport mode trunk switchport trunk allowed vlan 1-5 channel-group 200
New Deployments in a Dual-Homed FEX Topology

In a new deployment, configuration synchronization is introduced from the beginning to synchronize the configuration across peer switches. As a result, there is no existing running configuration on the FEX ports.

The following example shows how to configure the dual-homed FEX (active-active) topology:

  • Configure the CFS over IPV4 distribution to change the multicast address. 

    N9K-1(config)# no cfs ipv4 distributeThis will prevent CFS from distributing over IPv4 networkAre you sure? (y/n) [n] yN9K-2(config)# no cfs ipv4 distributeThis will prevent CFS from distributing over IPv4 network.Are you sure? (y/n) [n] y

  • Configure the CFSoIP multicast address on each peer switch. 

    N9K-1(config)# cfs ipv4 mcast-address 239.255.1.1Distribution over this IP type will be affectedChange multicast address for CFS-IP?Are you sure? (y/n) [n] yN9K-2# config terminalN9K-2(config)# cfs ipv4 mcast-address 239.255.1.1Distribution over this IP type will be affectedChange multicast address for CFS-IP?Are you sure? (y/n) [n] y

  • Enable CFSoIP on both switches. 

    N9K-1(config)# cfs ipv4 distributeN9K-2(config)# cfs ipv4 distribute

  • Create a switch profile on both switches. 

    N9K-1# config syncN9K-1(config-sync)# switch-profile TestN9K-1(config-sync-sp)# sync-peers destination /***out of band mgmt0 IP address of peer switch***/N9K-2>N9K-2# config syncN9K-2(config-sync)# switch-profile TestN9K-2(config-sync-sp)# sync-peers destination /***out of band mgmt0 IP address of peer switch***/N9K-1>

  • Add referred global configuration to the switch profile.

    Cisco Nexus 2000 Series NX-OS Fabric Extender Configuration Guide for Cisco Nexus 9000 Series Switches, Release 7.x - Configuring the Fabric Extender [Cisco Nexus 2000 Series Fabric Extenders] (12)

    Note

    Because interface configurations will be synchronized, all policies that are applied on the interface must be synchronized (for example, port profiles, QoS, and ACL policies). 

    N9K-1(config-sync-sp)# port-profile type ethernet eth-profileN9K-1(config-sync-port-prof)# switchport mode trunkN9K-1(config-sync-port-prof)# state enabledN9K-1(config-sync-sp)# port-profile type port-channel pc-profileN9K-1(config-sync-port-prof)# switchport mode trunkN9K-1(config-sync-port-prof)# state enabled

  • Configure the Ethernet interfaces (the non-port-channel members) inside the switch profile. 

    N9K-1(config-sync-sp)# interface Ethernet100/1/1N9K-1(config-sync-sp-if)# inherit port-profile eth-profileN9K-1(config-sync-sp-if)# switchport trunk allowed vlan 1-10

  • Create the port-channel interface inside the switch profile.

    Cisco Nexus 2000 Series NX-OS Fabric Extender Configuration Guide for Cisco Nexus 9000 Series Switches, Release 7.x - Configuring the Fabric Extender [Cisco Nexus 2000 Series Fabric Extenders] (13)

    Note

    You must configure port-channel interfaces in the switch profile, not in configuration terminal mode.

    This example shows that port channel 100 (vPC 100) is the EtherChannel from N9k to N2k: 

    N9K-1(config-sync-sp)# interface Port-channel100

    This example shows that port channel 200 is the EtherChannel from N2k to the end device: 

    N9K-1(config-sync-sp)# interface Port-channel200

  • Commit the configuration inside the switch profile. 

    N9K-1(config-sync-sp)# commit

  • Add members to the port channel in configuration terminal mode on both switches.

    Cisco Nexus 2000 Series NX-OS Fabric Extender Configuration Guide for Cisco Nexus 9000 Series Switches, Release 7.x - Configuring the Fabric Extender [Cisco Nexus 2000 Series Fabric Extenders] (14)

    Note

    The configuration must be done on both switches in configuration terminal mode.

    This example shows that N9k-1- Ethernet1/1 is a FEX-fabric member of port channel 100: 

    N9K-1(config)# int ether1/1N9K-1(config-if)# channel-group 100 force

    This example shows that N9K-1- Ethernet1/100/2-3 are members of port channel 200: 

    N9K-1(config)# interface Ethernet100/1/2-3N9K-1(config-if-range)# channel-group 200 force

    This example shows that N9K-2- Ethernet1/1 is a FEX-fabric interface that is in port channel 100: 

    N9K-2(config)# int ether1/1N9K-2(config-if)# channel-group 100 force

    This example shows that N9K-2- Ethernet1/100/2-3 are members of port channel 200: 

    N9K-2(config)# interface Ethernet100/1/2-3N9K-2(config-if-range)# channel-group 200 force
    N9K-1(config)# interface Ethernet100/1/2-3N9K-1(config-if-range)# switchport mode trunkN9K-1(config-if-range)# switchport trunk allowed vlan 1-5N9K-2(config)# interface Ethernet100/1/2-3N9K-2(config-if-range)# switchport mode trunkN9K-2(config-if-range)# switchport trunk allowed vlan 1-5

  • Modify the port-channel configuration in the switch profile. 

    N9K-1(config-sync-sp-if)# interface Port-Channel100N9K-1(config-sync-sp-if)# switchport mode fex-fabricN9K-1(config-sync-sp-if)# fex associate 101N9K-1(config-sync-sp-if)# vpc 100N9K-1(config-sync-sp)# interface Port-channel200N9K-1(config-sync-sp-if)# inherit port-profile pc-profileN9K-1(config-sync-sp-if)# switchport trunk allowed vlan 1-5

  • Commit the configuration in the switch profile. 

    N9K-1(config-sync-sp)# commit
Existing Deployment with a Dual-Homed FEX Topology

In an existing deployment, the configurations are already present and configuration synchronization is used to simplify future configuration modifications.

The following example shows how to configure the peer switches in the vPC topology for the dual-homed FEX (active-active) topology:

  • Configure the CFS over IPV4 distribution to change the multicast address. 
    N9K-1(config)# no cfs ipv4 distributeThis will prevent CFS from distributing over IPv4 networkAre you sure? (y/n) [n] yN9K-2(config)# no cfs ipv4 distributeThis will prevent CFS from distributing over IPv4 network.Are you sure? (y/n) [n] y
  • Configure the CFSoIP multicast address on each peer switch. 
    N9K-1(config)# cfs ipv4 mcast-address 239.255.1.1Distribution over this IP type will be affectedChange multicast address for CFS-IP?Are you sure? (y/n) [n] yN9K-2# config terminalN9K-2(config)# cfs ipv4 mcast-address 239.255.1.1Distribution over this IP type will be affectedChange multicast address for CFS-IP?Are you sure? (y/n) [n] y
  • Enable CFSoIP on both switches. 
    N9K-1(config)# cfs ipv4 distributeN9K-2(config)# cfs ipv4 distribute
  • Create a switch profile on both switches. 
    N9K-1# config syncN9K-1(config-sync)# switch-profile TestN9K-2# config syncN9K-2(config-sync)# switch-profile Test
  • Commit the configuration in the switch profile on both switches. 
    N9K-1(config-sync-sp)# commitN9K-2(config-sync-sp)# commit
  • Import the running configuration. 
    N9K-1(config-sync-sp)# import running-configN9K-1(config-sync-sp-import)# show switch-profile Test buffer

    Import the configuration to the switch profile on both switches. You can import the configuration using one of the following three methods:

    • Running configuration—All configurations that are allowed inside a switch profile are imported.

      You must remove unwanted configurations. For example, you must remove port-channel member configurations if the member interfaces do not match on the peer switches.

    • Interface configuration—Only specified interface configurations are imported.

    • Manual mode—Selected configurations are imported. If the configuration that needs to be imported is small, use the manual mode to paste the desired configuration.

      The following shows the command sequence to import the running configuration:

      Table 4. Command Sequence to Import the Running Configuration

      Buffer Sequence Number

      Command 

      1
      		 
      vlan 1-10
      		 
      22.12.22.3
      		 
      interface port-channel100 switchport mode fex-fabric vpc 100 fex associate 101
      		 
      33.13.2
      		 
      interface port-channel200 switchport mode trunk switchport trunk allowed vlan 1-5
      		 
      44.14.24.3
      		 
      interface Ethernet1/1 fex associate 101 switchport mode fex-fabric channel-group 100
      		 
      55.15.25.3
      		 
      interface Ethernet100/1/1 switchport mode trunk switchport trunk allowed vlan 1-10
      		 
      66.16.26.3
      		 
      interface Ethernet100/1/2 switchport mode trunk switchport trunk allowed vlan 1-5 channel-group 200
      		 
      77.17.27.3
      		 
      interface Ethernet100/1/3 switchport mode trunk switchport trunk allowed vlan 1-5 channel-group 200
  • Remove member interfaces of PO 100 and PO 200 from the buffer. 
    N9K-1(config-sync-sp-import)# buffer-delete 4, 6, 7

    Use the buffer-delete command to delete the unwanted configuration from the buffer.

  • Commit the configuration in the switch profile on both switches. 
    N9K-1(config-sync-sp-import)# commitN9K-2(config-sync-sp-import)# commit
  • Add the sync peer on both switches.
    Cisco Nexus 2000 Series NX-OS Fabric Extender Configuration Guide for Cisco Nexus 9000 Series Switches, Release 7.x - Configuring the Fabric Extender [Cisco Nexus 2000 Series Fabric Extenders] (15)

    Note

    When importing the configuration, you must use the sync-peers command after the configurations are imported independently on both switches. 

    N9K-1# config syncN9K-1(config-sync)# switch-profile spN9K-1(config-sync-sp)# sync-peers destination /***out of band mgmt0 IP address of peer switch***/N9K-2>N9K-2# config syncN9K-2(config-sync)# switch-profile spN9K-2(config-sync-sp)# sync-peers destination /***out of band mgmt0 IP address of peer switch***/N9K-1>
    N9K-1# configure syncEnter configuration commands, one per line. End with CNTL/Z.N9K-1(config-sync)# no switch-profile SP ? all-config Deletion of profile, local and peer configurations local-config Deletion of profile and local configuration profile-only Deletion of profile only and no other configuration N9396PX-1(config-sync)# no switch-profile SP
    Cisco Nexus 2000 Series NX-OS Fabric Extender Configuration Guide for Cisco Nexus 9000 Series Switches, Release 7.x - Configuring the Fabric Extender [Cisco Nexus 2000 Series Fabric Extenders] (16)

    Caution

    When you remove a switch profile using the no switch-profile name [all-config | local-config] command, the configuration in the switch profile is immediately removed from the running configuration. This disrupts the configurations that were present in the switch profile, such as port channel and vPC configurations.

    When you remove a switch profile using the no switch-profile name [profile-only] command, the configuration in the switch profile is immediately removed from the switch profile only. This does not disrupt the configurations that were present in running config.

    It is recommended to execute the CLI resync-database on both peer switches before deleting a large configuration in the switch-profile.

    Perform the following action if you received the "Deletion of switch profile failed" error message when attempting to delete switch-profile:
     N9K-1(config-sync)# resync-databaseRe-synchronization of switch-profile db takes a few minutes...Re-synchronize switch-profile db completed successfully.N9K-1(config-sync)#N9K-2(config-sync)# resync-databaseRe-synchronization of switch-profile db takes a few minutes...Re-synchronize switch-profile db completed successfully.N9K-2(config-sync)#

Verifying the Configuration

This section describes how to display the configuration of the Fabric Extender and verify the chassis hardware status.

Verifying the Fabric Extender Configuration

Use the following commands to display configuration information about the defined interfaces on a Fabric Extender:

Command or Action

Purpose

show fex [ FEX-number] [ detail]

Displays information about a specific Fabric Extender or all attached units.

show interface type number fex-intf

Displays the Fabric Extender ports that are pinned to a specific switch interface.

show interface fex-fabric

Displays the switch interfaces that have detected a Fabric Extender uplink.

show interface ethernet number transceiver [ fex-fabric]

Displays the SFP+ transceiver and diagnostic optical monitoring (DOM) information for the Fabric Extender uplinks.

show feature-set

Displays the status of the feature sets on the device.

Configuration Examples for the Fabric Extender

This example shows how to display all the attached Fabric Extender units: 

switch# show fex FEX FEX FEX FEXNumber Description State Model Serial------------------------------------------------------------------------101 FEX0101 Online N2K-C2248TP-1GE JAF1418AARL

This example shows how to display the detailed status of a specific Fabric Extender: 

switch# show fex 101 detailFEX: 101 Description: FEX0101 state: Online FEX version: 5.1(1) [Switch version: 5.1(1)] FEX Interim version: 5.1(0.159.6) Switch Interim version: 5.1(1) Extender Model: N2K-C2248TP-1GE, Extender Serial: JAF1418AARL Part No: 73-12748-05 Card Id: 99, Mac Addr: 54:75:d0:a9:49:42, Num Macs: 64 Module Sw Gen: 21 [Switch Sw Gen: 21] pinning-mode: static Max-links: 1 Fabric port for control traffic: Po101 Fabric interface state: Po101 - Interface Up. State: Active Eth2/1 - Interface Up. State: Active Eth2/2 - Interface Up. State: Active Eth4/1 - Interface Up. State: Active Eth4/2 - Interface Up. State: Active Fex Port State Fabric Port Primary Fabric Eth101/1/1 Up Po101 Po101 Eth101/1/2 Up Po101 Po101 Eth101/1/3 Down Po101 Po101 Eth101/1/4 Down Po101 Po101 Eth101/1/5 Down Po101 Po101 Eth101/1/6 Down Po101 Po101 Eth101/1/7 Down Po101 Po101 Eth101/1/8 Down Po101 Po101 Eth101/1/9 Down Po101 Po101 Eth101/1/10 Down Po101 Po101 Eth101/1/11 Down Po101 Po101 Eth101/1/12 Down Po101 Po101 Eth101/1/13 Down Po101 Po101 Eth101/1/14 Down Po101 Po101 Eth101/1/15 Down Po101 Po101 Eth101/1/16 Down Po101 Po101 Eth101/1/17 Down Po101 Po101 Eth101/1/18 Down Po101 Po101 Eth101/1/19 Down Po101 Po101 Eth101/1/20 Down Po101 Po101 Eth101/1/21 Down Po101 Po101 Eth101/1/22 Down Po101 Po101 Eth101/1/23 Down Po101 Po101 Eth101/1/24 Down Po101 Po101 Eth101/1/25 Down Po101 Po101 Eth101/1/26 Down Po101 Po101 Eth101/1/27 Down Po101 Po101 Eth101/1/28 Down Po101 Po101 Eth101/1/29 Down Po101 Po101 Eth101/1/30 Down Po101 Po101 Eth101/1/31 Down Po101 Po101 Eth101/1/32 Down Po101 Po101 Eth101/1/33 Down Po101 Po101 Eth101/1/34 Down Po101 Po101 Eth101/1/35 Down Po101 Po101 Eth101/1/36 Down Po101 Po101 Eth101/1/37 Down Po101 Po101 Eth101/1/38 Down Po101 Po101 Eth101/1/39 Down Po101 Po101 Eth101/1/40 Down Po101 Po101 Eth101/1/41 Down Po101 Po101 Eth101/1/42 Down Po101 Po101 Eth101/1/43 Down Po101 Po101 Eth101/1/44 Down Po101 Po101 Eth101/1/45 Down Po101 Po101 Eth101/1/46 Down Po101 Po101 Eth101/1/47 Down Po101 Po101 Eth101/1/48 Down Po101 Po101Logs:09/21/2010 21:14:26.843850: Module register received09/21/2010 21:14:26.845778: Registration response sent09/21/2010 21:14:27.663073: Module Online Sequence09/21/2010 21:14:30.191121: Module Online

This example shows how to display the Fabric Extender interfaces pinned to a specific switch interface: 

switch# show interface port-channel 101 fex-intfFabric FEXInterface Interfaces--------------------------------------------------- Po101 Eth101/1/2 Eth101/1/1

This example shows how to display the switch interfaces that are connected to a Fabric Extender uplink: 

switch# show interface fex-fabric Fabric Fabric Fex FEXFex Port Port State Uplink Model Serial---------------------------------------------------------------101 Eth2/1 Active 1 N2K-C2248TP-1GE JAF1418AARL101 Eth2/2 Active 2 N2K-C2248TP-1GE JAF1418AARL101 Eth4/1 Active 3 N2K-C2248TP-1GE JAF1418AARL101 Eth4/2 Active 4 N2K-C2248TP-1GE JAF1418AARL

This example shows how to display the SFP+ transceiver and diagnostic optical monitoring (DOM) information for Fabric Extender uplinks for an SFP+ transceiver that is plugged into the parent switch interface: 

switch# show interface ethernet 1/40 transceiverEthernet1/40 sfp is present name is CISCO-MOLEX INC part number is 74752-9026 revision is A0 serial number is MOC13321057 nominal bitrate is 12000 MBits/sec Link length supported for copper is 3 m(s) cisco id is -- cisco extended id number is 4

This example shows how to display the SFP+ transceiver and DOM information for Fabric Extender uplinks for an SFP+ transceiver that is plugged into the uplink port on the Fabric Extender: 

switch# show interface ethernet 1/40 transceiver fex-fabricEthernet1/40 sfp is present name is CISCO-MOLEX INC part number is 74752-9026 revision is A0 serial number is MOC13321057 nominal bitrate is 12000 MBits/sec Link length supported for 50/125mm fiber is 0 m(s) Link length supported for 62.5/125mm fiber is 0 m(s) cisco id is -- cisco extended id number is 4

Verifying the Chassis Management Information

Use the following to display configuration information used on the switch supervisor to manage the Fabric Extender.

Command or Action

Purpose

show environment fex {all | FEX-number} [temperature | power | fan]

Displays the environmental sensor status.

show inventory fex FEX-number

Displays inventory information for a Fabric Extender.

show module fex [FEX-number]

Displays module information about a Fabric Extender.

show sprom fex FEX-number {all | backplane | powersupply ps-num} | all

Displays the contents of the serial PROM (SPROM) on the Fabric Extender.

Configuration Examples for Chassis Management

This example shows how to display the module information about all connected Fabric Extender units:

This example shows how to display the inventory information about a specific Fabric Extender: 

switch# show inventory fex 101NAME: "FEX 101 CHASSIS", DESCR: "N2K-C2248TP-1GE CHASSIS"PID: N2K-C2248TP-1GE , VID: V00 , SN: SSI13380FSMNAME: "FEX 101 Module 1", DESCR: "Fabric Extender Module: 48x1GE, 4x10GE Supervisor"PID: N2K-C2248TP-1GE , VID: V00 , SN: JAF1339BDSKNAME: "FEX 101 Fan 1", DESCR: "Fabric Extender Fan module"PID: N2K-C2248-FAN , VID: N/A , SN: N/ANAME: "FEX 101 Power Supply 2", DESCR: "Fabric Extender AC power supply"PID: NXK-PAC-400W , VID: 000, SN: LIT13370QD6

This example shows how to display the environment status for a specific Fabric Extender: 

switch# show environment fex 101Temperature Fex 101:-----------------------------------------------------------------Module Sensor MajorThresh MinorThres CurTemp Status (Celsius) (Celsius) (Celsius)-----------------------------------------------------------------1 Outlet-1 60 50 33 ok1 Outlet-2 60 50 38 ok1 Inlet-1 50 40 35 ok1 Die-1 100 90 44 okFan Fex: 101:------------------------------------------------------Fan Model Hw Status------------------------------------------------------Chassis N2K-C2148-FAN -- okPS-1 -- -- absentPS-2 NXK-PAC-400W -- okPower Supply Fex 101:---------------------------------------------------------------------------Voltage: 12 Volts-----------------------------------------------------PS Model Power Power Status (Watts) (Amp)-----------------------------------------------------1 -- -- -- --2 NXK-PAC-400W 4.32 0.36 okMod Model Power Power Power Power Status Requested Requested Allocated Allocated (Watts) (Amp) (Watts) (Amp)--- ------------------- ------- ---------- --------- ---------- ----------1 N2K-C2248TP-1GE 0.00 0.00 0.00 0.00 powered-upPower Usage Summary:--------------------Power Supply redundancy mode: redundantTotal Power Capacity 4.32 WPower reserved for Supervisor(s) 0.00 WPower currently used by Modules 0.00 W -------------Total Power Available 4.32 W -------------

This example shows how to display the SPROM for a specific Fabric Extender: 

switch# show sprom fex 101 allDISPLAY FEX 101 SUP sprom contentsCommon block: Block Signature : 0xabab Block Version : 3 Block Length : 160 Block Checksum : 0x1a1e EEPROM Size : 65535 Block Count : 3 FRU Major Type : 0x6002 FRU Minor Type : 0x0 OEM String : Cisco Systems, Inc. Product Number : N2K-C2248TP-1GE Serial Number : JAF1339BDSK Part Number : 73-12748-01 Part Revision : 11 Mfg Deviation : 0 H/W Version : 0.103 Mfg Bits : 0 Engineer Use : 0 snmpOID : 9.12.3.1.9.78.3.0 Power Consump : 1666 RMA Code : 0-0-0-0 CLEI Code : XXXXXXXXXTBDV00 VID : V00Supervisor Module specific block: Block Signature : 0x6002 Block Version : 2 Block Length : 103 Block Checksum : 0x2686 Feature Bits : 0x0 HW Changes Bits : 0x0 Card Index : 11016 MAC Addresses : 00-00-00-00-00-00 Number of MACs : 0 Number of EPLD : 0 Port Type-Num : 1-48;2-4 Sensor #1 : 60,50 Sensor #2 : 60,50 Sensor #3 : -128,-128 Sensor #4 : -128,-128 Sensor #5 : 50,40 Sensor #6 : -128,-128 Sensor #7 : -128,-128 Sensor #8 : -128,-128 Max Connector Power: 4000 Cooling Requirement: 65 Ambient Temperature: 40DISPLAY FEX 101 backplane sprom contents:Common block: Block Signature : 0xabab Block Version : 3 Block Length : 160 Block Checksum : 0x1947 EEPROM Size : 65535 Block Count : 5 FRU Major Type : 0x6001 FRU Minor Type : 0x0 OEM String : Cisco Systems, Inc. Product Number : N2K-C2248TP-1GE Serial Number : SSI13380FSM Part Number : 68-3601-01 Part Revision : 03 Mfg Deviation : 0 H/W Version : 1.0 Mfg Bits : 0 Engineer Use : 0 snmpOID : 9.12.3.1.3.914.0.0 Power Consump : 0 RMA Code : 0-0-0-0 CLEI Code : XXXXXXXXXTDBV00 VID : V00Chassis specific block: Block Signature : 0x6001 Block Version : 3 Block Length : 39 Block Checksum : 0x2cf Feature Bits : 0x0 HW Changes Bits : 0x0 Stackmib OID : 0 MAC Addresses : 00-0d-ec-e3-28-00 Number of MACs : 64 OEM Enterprise : 0 OEM MIB Offset : 0 MAX Connector Power: 0WWN software-module specific block: Block Signature : 0x6005 Block Version : 1 Block Length : 0 Block Checksum : 0x66wwn usage bits: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00License software-module specific block: Block Signature : 0x6006 Block Version : 1 Block Length : 16 Block Checksum : 0x86flic usage bits: ff ff ff ff ff ff ff ffDISPLAY FEX 101 power-supply 2 sprom contents:Common block: Block Signature : 0xabab Block Version : 3 Block Length : 160 Block Checksum : 0x1673 EEPROM Size : 65535 Block Count : 2 FRU Major Type : 0xab01 FRU Minor Type : 0x0 OEM String : Cisco Systems Inc NXK-PAC-400W Product Number : NXK-PAC-400W Serial Number : LIT13370QD6 Part Number : 341 Part Revision : -037 CLEI Code : 5-01 01 000 VID : 000 snmpOID : 12336.12336.12336.12336.12336.12336.12374.12336 H/W Version : 43777.2 Current : 36 RMA Code : 200-32-32-32Power supply specific block: Block Signature : 0x0 Block Version : 0 Block Length : 0 Block Checksum : 0x0 Feature Bits : 0x0 Current 110v : 36 Current 220v : 36 Stackmib OID : 0

Additional References

This section includes additional information that is related to configuring the Cisco Nexus 2000 Series Fabric Extender.

Related Documents

Related Topic

Document Title

Cisco NX-OS Licensing

Cisco NX-OS Licensing Guide

Interface configuration

Cisco Nexus 9000 Series NX-OS Interfaces Configuration Guide

Command reference

Cisco Nexus 9000 Series Command References

Cisco Nexus 2000 Series NX-OS Fabric Extender Configuration Guide for Cisco Nexus 9000 Series Switches, Release 7.x - Configuring the Fabric Extender [Cisco Nexus 2000 Series Fabric Extenders] (2024)
Top Articles
D2L Course Accessibility | Michigan State University
Training | Michigan State University
Rats Local Snitches List
Brain And Spine Surgical Navigation Rep Salary
Klustron 9
Estate Sales Net Grand Rapids
Bed Bath And Beyond Gulfport Ms
Jesuit Resource - Black History Month Quotes
Game8 Jingliu
Uncc Residence Life
Roue Avant 10 X 3.50 - No Disque MBK BOOSTER 50 1994 1995 3WW • EUR 35,06
Carénage Bouclier Arrière Charactère des ´ Gn MBK BOOSTER 50 1992 1994 3WW • EUR 31,89
Latest Posts
How fungi elude antifungal treatments
Dillypen
Article information

Author: Reed Wilderman

Last Updated:

Views: 5674

Rating: 4.1 / 5 (72 voted)

Reviews: 87% of readers found this page helpful

Author information

Name: Reed Wilderman

Birthday: 1992-06-14

Address: 998 Estell Village, Lake Oscarberg, SD 48713-6877

Phone: +21813267449721

Job: Technology Engineer

Hobby: Swimming, Do it yourself, Beekeeping, Lapidary, Cosplaying, Hiking, Graffiti

Introduction: My name is Reed Wilderman, I am a faithful, bright, lucky, adventurous, lively, rich, vast person who loves writing and wants to share my knowledge and understanding with you.