Air Fuel Ratio / O2 Sensor: how it works, problems, testing (2024)

Home > How car parts and sensors work > Air Fuel Ratio / O2 Sensor

Updated: September 13, 2021

In the early 00's conventional oxygen sensors gave way to more precise air fuel ratio sensors, although they are still referred to as 'oxygen sensors' or O2 sensors.

Air fuel (A/F) ratio sensor

The air fuel ratio (A/F) sensor measures oxygen content of the exhaust in a wider range. It is also known as the "broadband lambda sensor" or "lambda probe."

The air fuel ratio sensor is installed in the exhaust manifold or in the front exhaust pipe, before the catalytic converter. It might also be called 'front O2 sensor'. The job of the air fuel ratio sensor is to measure the oxygen content in the exhaust and provide feedback to the engine computer (PCM). Based on air fuel ratio sensor signal, the computer adjusts the air to fuel ratio to keep it at the optimum level, which is about 14.7:1 or 14.7 parts of air to 1 part of fuel.

Air fuel ratio sensor problems

Problems with air fuel ratio sensors are common. Often a sensor gets contaminated or simply fails. In some cars, the heating element inside the sensor can stop working and cause the malfunction. For example, in many Toyota and Honda cars the code P0135 may be caused by a failed heating element inside the sensor. See how the heating element of the A/F sensor is checked in this article: code P0135.

In some cars, a sensor wiring may get shorted out after rubbing against metal parts. For example, in older Mazda 3, the sensor wire may rub against the bracket and short out causing the code P0131. When the engine computer detects that the air fuel ratio sensor signal is out of expected range it illuminates the check engine light.

Most common OBDII trouble codes related to an air fuel ratio sensor are P0131, P0134, P0135, P0133, P0031 and P1135. Are there any symptoms besides the Check Engine light? In some cars you may notice a drop in the fuel economy or some driveability issues.

Air fuel ratio sensor diagnostic

An air fuel ratio sensor is diagnosed following the manufacturer's troubleshooting procedure for the trouble code that has been set. The first step is to check for related technical service bulletins (TSBs). The wiring and the connector of the sensor must be checked for damage, corrosion, loose pins, etc.

Checking the air fuel ratio sensor with a scan tool.

Then, depending on the trouble code, the sensor signal must be tested with a scan tool. For example, see this chart of the air-fuel ratio sensor signal on a scan tool: when the engine is revved, the signal jumps to "rich", then as the RPM drops and the fuel is cut off, the sensor indicates "lean". After that, the signal goes back to normal. This air fuel sensor works properly.

Often, the sensor may work properly at the time of the inspection. In this case, your mechanic may recommend replacing the air fuel ratio sensor to eliminate the possibility of an intermittent fault.

Rear Oxygen Sensor

Air Fuel Ratio / O2 Sensor: how it works, problems, testing (3) Rear (downstream) oxygen sensor diagram

The rear or downstream oxygen sensor is installed in the exhaust after the catalytic converter. It measures the amount of oxygen in the exhaust gases coming out of the catalytic converter. The signal from the rear oxygen sensor is used to monitor the efficiency of the catalytic converter. Read more: Catalytic Converter: problems, replacement options.

The engine computer or PCM constantly compares the signals from the front and the rear oxygen sensors (see the diagram). Based on the two signals, the PCM knows how well the catalytic converter does its job. If the catalytic converter fails, the PCM turns on the "Check Engine" light to let you know.
The rear oxygen sensor can be checked with a scan tool or a lab scope.

Air Fuel Ratio/Oxygen Sensor Identification

The front oxygen sensor or air fuel ratio sensor is installed before the catalytic converter; it's called an 'upstream' or 'Sensor 1'.
The rear oxygen sensor installed after the catalytic converter is called 'downstream' or Sensor 2.
A typical in-line 4-cylinder engine has only one bank (Bank 1). Therefore, in an in-line 4-cylinder engine, the term "Bank 1, Sensor 1" simply refers to the front oxygen sensor. "Bank 1, Sensor 2" is the rear oxygen sensor.

Air Fuel Ratio / O2 Sensor: how it works, problems, testing (4) Typically, the engine bank that
contains cylinder 1 is called Bank 1

The V6 or V8 engine has two banks (or two parts of that "V"). Usually, the bank that contains the cylinder number 1 is called "Bank 1."

Different car manufacturers define Bank 1 and Bank 2 differently. To know which is Bank 1 and Bank 2 in your car, you can look it up in a repair manual or you can google it, mentioning the year, make, model and engine size of your car. For example, according to the Toyota bulletin TSB-0398-09, in a V6 Camry, Highlander, Avalon, Sienna and Solara, bank 1 is at the back, bank 2 is in the front. Similarly, in a V6 2003-2008 Mazda 6 or V6 Mazda Tribute, bank 1 is at the back, bank 2 is at the front. In a 2003 Nissan Maxima, bank 1 is at the back, bank 2 is at the front.

Replacing Air Fuel Ratio/Oxygen Sensor

In most cars, replacing an oxygen sensor is a fairly simple job unless it's difficult to access. In a repair shop, oxygen sensor replacement costs from $50 to $250 (labor only).

Advertisem*nt

If you want to replace the oxygen sensor yourself, with some skills and a repair manual, it's not so difficult, but you might need a special oxygen sensor socket (in the photo below).
Sometimes it might be difficult to remove an old sensor, as it could be seized in its thread. We found several videos on how to remove a seized O2 sensor.

When replacing an air fuel sensor there are two options: to install an original (OEM) or aftermarket part. Aftermarket sensors work fine most of the time. However, we came across several cases where an aftermarket sensor was causing the problem that was fixed after installing an OEM sensor.

Air Fuel Ratio / O2 Sensor: how it works, problems, testing (5) Replacing the oxygen sensor

If the price is comparable, using an OEM sensor is a better option. Another reason to use an OEM sensor is that often manufacturers update the part design to eliminate problems that were discovered after the production.

For California-certified cars, the part number for the air fuel ratio sensor might be different. It's best to order the correct part using your VIN number.

Read Next:
Vacuum leaks: problems, symptoms, repairs
What causes an engine to misfire
Mass Air Flow Sensor (MAF): how it works, symptoms, problems, testing
Check Engine light: what to check, common problems, repair options
How car parts and sensors work

Air Fuel Ratio / O2 Sensor: how it works, problems, testing (2024)
Top Articles
Map Test Log In
MetLife Stadium Seating Chart + Section, Row & Seat Number Info
Melfme
Craigslist Dog Sitter
Pbr Wisconsin Baseball
R Tiktoksweets
Bc Hyundai Tupelo Ms
3472542504
United Dual Complete Providers
Cooking Fever Wiki
I Wanna Dance with Somebody : séances à Paris et en Île-de-France - L'Officiel des spectacles
Sivir Urf Runes
Available Training - Acadis® Portal
Nashville Predators Wiki
Craigslist Portland Oregon Motorcycles
Ibukunore
Espn Horse Racing Results
Craigslist St. Cloud Minnesota
Betaalbaar naar The Big Apple: 9 x tips voor New York City
R&S Auto Lockridge Iowa
Pioneer Library Overdrive
Shia Prayer Times Houston
Log in or sign up to view
Florence Y'alls Standings
Tokioof
Pipa Mountain Hot Pot渝味晓宇重庆老火锅 Menu
DIY Building Plans for a Picnic Table
Warn Notice Va
Wisconsin Volleyball Team Leaked Uncovered
Home Auctions - Real Estate Auctions
Restaurants Near Calvary Cemetery
Http://N14.Ultipro.com
Craigslist Central Il
Craigslist Dallastx
Golden Tickets
Wow Quest Encroaching Heat
Synchrony Manage Account
Bernie Platt, former Cherry Hill mayor and funeral home magnate, has died at 90
Oriellys Tooele
Bartow Qpublic
The best bagels in NYC, according to a New Yorker
Giovanna Ewbank Nua
Levi Ackerman Tattoo Ideas
Craigslist Houses For Rent Little River Sc
Stephen Dilbeck, The First Hicks Baby: 5 Fast Facts You Need to Know
Craigslist Charles Town West Virginia
Blog Pch
What Time Do Papa John's Pizza Close
The Goshen News Obituary
Myhrkohls.con
Ark Silica Pearls Gfi
login.microsoftonline.com Reviews | scam or legit check
Latest Posts
Article information

Author: Ray Christiansen

Last Updated:

Views: 5708

Rating: 4.9 / 5 (49 voted)

Reviews: 88% of readers found this page helpful

Author information

Name: Ray Christiansen

Birthday: 1998-05-04

Address: Apt. 814 34339 Sauer Islands, Hirtheville, GA 02446-8771

Phone: +337636892828

Job: Lead Hospitality Designer

Hobby: Urban exploration, Tai chi, Lockpicking, Fashion, Gunsmithing, Pottery, Geocaching

Introduction: My name is Ray Christiansen, I am a fair, good, cute, gentle, vast, glamorous, excited person who loves writing and wants to share my knowledge and understanding with you.